/

    Demattia Flex-Cracking Tester

    Model: GT-7011-D


    Standard conformance: BS 903-A10: 1999, JIS K6301, and JIS K6260-1999.

    The GT-7011-D is designed to assess the resistance of vulcanized rubber to crack growth when subjected to repeated flexing. 

    Features:
    1. Well-suited for industries such as rubber manufacturing, automotive, medical devices, electronics, and industrial manufacturing. 
    2. Delivers reliable performance with adjustability and repeatability.
/

    Shoe Bending Waterproofness Tester

    Model: GT-7011-SWH1


    Standard conformance: GB/T16641-2019 and ISO 20344：2021.

    The GT-7011-SWH1 is designed to evaluate the water resistance of various types of finished shoes under dynamic conditions.

    Features:
    1. Equipped with pneumatic simulated foot to effectively secure specimens.
    2. Self-detection sensor for water penetration. Auto-stop triggered by water penetration.
    3. Features a dual-station design for testing two specimens at the same time.
    4. Intuitive and easy-to-use touchscreen controller.

/

    Youth Shoe Flexing Fixture

    Model: GT-7011-SWK


    The GT-7011-SWK fixture is designed for bending waterproofness testing of youth shoes on the GT-7011-SWN2 tester. It securely holds the youth shoe specimen in place, ensuring accurate and reliable results.

/

    Plastic Hydraulic Molding Press

    Model:GT-7014-EPC


    The GT-7014-EPC is designed to form materials into test samples for materials testing.

    Features:
    1. Intuitive and easy-to-use touchscreen interface with support for user-defined test programs.
    2. Ensures stable control in high temperautre and pressure, providing reliable operation.
    3. Equipped with multiple safety features, including overloading protection, to ensure safe operation.

/

    Drop Ball Impact Tester

    Model:GT-7037-ST


    The GT-7037-ST drop ball impact tester is specifically designed to determine the resistance of sheet, film, and lining materials to impact.

    Features:
    1. Equipped with a guide tunnel and ball blocker, this tester allows steel ball to drop at a specified height for testing. The ball blocker ensures operational safety by preventing accidental drops of the steel ball during specimen installation.
    2. Equipped with safety stop devices to prevent rebound impact.

/

    Drop Impact Tester

    Model:GT-7037-H2


    The GT-7037-H2 is specifically designed to evaluate the impact resistance of long specimens. It utilizes an electromagnet-controlled striker to perform free-drop impacts at a specified height.

/

    Coated Fabrics Flexing Tester

    Model: GT-7043-M4


    Standard conformance: GB/T 1256 Method C, ISO 7854 Method C, and GB 8965.3-2022 5.14.

    The GT-7043-M4 is designed to evaluate the resistance of coated fabrics to damage under repeated flexing.

    Features:
    1. Intuitive and user-friendly HMI touchscreen interface.
    2. Holds specimens securely using adjustable clamping ring, ensuring reliable test results.

/

    Oil Seal Radial Force Tester

    Model: GT-7074-OST


    This oil seal radial force tester is specifically designed to measure the radial force exerted by a radial shaft seal within a defined time to evaluate its sealing performance. It features a split shaft design, with one half connected to a load cell. After the radial shaft seal is applied, the operating system automatically captures the radial force once the specified duration is reached.

/

    Hose Layer Adhesion Testing Fixture

    Model: FC-9-4B


    Standard conformance: GB/T-14905

    This fixture is designed to determine the adhesion strength of laminated hoses.

    Features:
    ‧ Gripping type: Manually operated.
    ‧ Structure: Configured with a rotational mandrel-type upper fixture and a plier-type lower grip to ensure stable specimen clamping.
    ‧ Application: Applicable to adhesion testing of different types of laminated rubber and plastic hoses.

/

    Tape Unwinding Force Fixture

    Model: FC-9-4C


    Standard conformance: GB/T 4850-2002.

    This fixture is used to determine the unwinding force of pressure-sensitive adhesive tapes at low speed.

    Features:
    ‧ Gripping type: Manual+pneumatic gripping.
    ‧ Structure: This lower fixture is designed for clamping specimen with a width not exceeding 80mm.
    ‧ Application: Suitable for unwinding rolled adhesive tape without release liner.

/

    Cable Bending Fixture

    Model: B-R200


    This fixture is specifically designed for performing 3-point bending tests on electrical cables.

    Features:
    ‧ Gripping type: Manually operated.
    ‧ Structure: Span-adjustable pulley supports.
    ‧ Application: Suitable for thin electrical cables.

/

    Cable Bending Fixture

    Model: B-R500


    This fixture is specifically designed for performing 3-point bending tests on electrical cables.

    Features:
    ‧ Gripping type: Manually operated.
    ‧ Structure: Span-adjustable pulley-supports.
    ‧ Application: Suitable for thick electrical cables.

/

    Rivet Pull-Out Fixture

    Model: RB-7-14


    This fixture is specifically designed for performing pull-out tests on metal rivets. The rivet specimen is clamped between two jaw faces and secured by a lever mechanism. It is then subjected to tensile force at a specified speed to determine its pull-out strength and extension.

/

    Metal Grips

    Model: MB-2TN

     

    The MB-2TN metal grips are used for performing tensile tests on materials to determine their elongation, maximum load, and breaking strength.

    Features:
    ‧ Gripping type: Manually operated and spring self-tightening.
    ‧ Structure: The operating handle is set with a limiter, ensuring quick and easy specimen installation.
    ‧ Application: Suitable for testing on rubber, metal sheet, and soft plastics.

/

    Cable Tensile Grips

    Model: WA-1E

     

    Standard conformance: ISO 19642-2-2023 5.4.3.

    The cable tensile grips are specifically designed to determine the tensile force required to break electrical cables.

    Features:
    ‧ Gripping type: Manually operated.
    ‧ Structure: Designed with a ring-wrapping mechanism to improve clamping and reduce specimen slippage during testing.
    ‧ Application: Suitable for electrical cables ≦6mm2.

/

    Pneumatic Tensile Grips

    Model: AP-1D

     

    With a compact and lightweight design, these pneumatic grips are easy to install and operate, making them ideal for tensile testing of long specimens. They apply tensile force along the specimen's length to determine its breaking strength and extension rate.

/

    Handle Tensile Fixture

    Model: B-T1

     

    The handle specimen is mounted on the lower grip, with a webbing strap threaded through it and secured by the upper grip. A tensile load is then applied via the webbing at a specified speed to determine the breaking strength and extension rate of the handle specimen.

/

    Remote Control

    Model: CT-1

     

    The CT-1 remote control offers convenient operation of the UTM, featuring essential functions such as test start/stop and crosshead movement control for both testing and specimen setup.

Back to the top