/

    Coated Fabrics Flexing Tester

    Model: GT-7011-IB


    Standard conformance: ISO 7854 method B and GB/T 12586-2003 method B.

    The GT-7011-IB is specifically designed to assess the resistance of coated fabrics to damage by repeated flexing under various temperature and humidity conditions.

    Features:
    1. Supports both counter and timer test modes to determine the maximum number of flexes required to cause damage to coated fabrics. 
    2. Equipped with an advanced touchscreen controller, the GT-7011-IB offers an intuitive and user-friendly experience, along with program operation and status display.
    3. Provides a wide range of temperature and humidity settings, allowing users to monitor the preset and real-time conditions through a trend graph.
/

    Coated Fabrics Flexing Tester

    Model: GT-7011-IB1


    Standard conformance: GB/T 24539-2021 appendix K and GB/T 12586-2003 method B.

    The GT-7011-IB is specifically designed to assess the resistance of coated fabrics to damage by repeated flexing.

    Features:
    Supports both counter and timer test modes to determine the maximum number of flexes required to cause damage to coated fabrics.

/

    Martindale Abrasion Tester

    Model: GT-7012-M9


    Standard conformance: GB/T 21196.2 and GB/T 4802.2.

    The GT-7012-M9 is specifically designed to determine the durability and resistance of textile fabrics to dry or wet abrasion. 

    Features:
    1. Allows up to 9 specimens to be tested simultaneously and supports user-defined station setup.
    2. Meets testing requirements for dry and wet abrasion, as well as tearing tests.
    3. With its advanced PLC and HMI controller, the GT-7012-M9 delivers intuitive control, auto-stop function, auto-lifting motion plate, and data memory capabilities.

/

    Digital Type Bursting Strength Tester

    Model: GT-7013-MPA


    Standard conformance: GB/T 1539, ASTM D3786, ISO 2758, GB/T 454, TAPPI T403, and ASTM D3786M-18.

    The GT-7013-MPA is designed to assess the bursting strength of various materials, including corrugated paper, leather, and fabrics.

    Features:
    Provides auto/manual test modes, enabling automatic detection, gripping and testing of test specimens, along with automatic data calculation, storage, and printing capabilities.

/

    Servo-Controlled Molding Press

    Model: GT-7014-SU1


    The GT-7014-SU1 offers intuitive control and precision to shape and form materials under high temperature and pressure for test specimen preparation.


    Features:
    1. Constructed with low capacity singl-station, precision servo-controlled motor system, and efficient cooling system.
    2. Provides intuitive operation experience, supports temperature trend graph, and deliver efficient cooling using advanced PLC and HMI controller.
    3. Utilizes dedicated computer system to control and regulate test loads.

/

    Fabrics Fuzzing and Pilling Tester

    Model: GT-7028-PA


    Standard conformance: GB/T 4802.1-2008.

    The GT-7028-PA is specifically designed to determine the fabrics propensity to surface fuzzing and pilling using circular locus method.

    Features:
    1. Provides switchable testing configuration between fuzzing and pilling station.
    2. Intuitive and user-friendly touchscreen interface.

/

    Automatic Sample Feeding and Cooling System

    Model: GT-7045-A02


    The GT-7045-A02 is an optional auxiliary device that enables the GT-7045-ALN impact tester to perform impact testing under low temperature conditions for plastic materials. 

    Features:
    1. The GT-7045-A02 combines automatic sample feeding and cooling systems for Charpy testing, offering both liquid nitrogen and compressor cooling options.
    2. It moves the magazine filled with samples into the cooling bath for conditioning. Once the cooling is completed, activating the auto-feeding enables samples to be loaded and centered for impact testing.
     

/

    Insole Reciprocating Compression Tester

    Model: GT-7049-CIP


    The GT-7049-CIP is specifically designed to assess the performance of insole under repeated compression.

    Features:
    Provides an intuitive and user-friendly interface, allowing users to adjust compression cycles and activating auto-stop upon test completion.

/

    Drop Impact Tester

    Model: GT-7066-D


    The GT-7066-D is specifically designed to evaluate the impact resistance of long specimens, such as hockey sticks. To conduct this assessment, it utilizes an electromagnet-controlled striker to perform free-drop impacts at a specified height.

     

/

    Rubber Rolling Resistance Tester

    Model: GT-7082-R


    The GT-7082-R is specifically designed to determine the rolling resistance of rubber materials. By utilizing the drum method, this instrument can assess the power loss of vulcanized rubber under specific frequencies and loads, offering valuable insights into rolling resistance for research and development of rubber material formulations.

    Features:
    1. This instrument integrates advanced modular design, dedicated software, a servo-controlled system, and an infrared temperature detector to precisely measure the power loss of vulcanized rubber under specific frequencies and loads.
    2. Provides test conditions aligned with real-world scenarios of tire tread in use, ensuring test accuracy and repeatability.
    3. Features easy operation, real-time monitoring, data storage, and printing capability.

/

    Shuttlecock Head Height Gauge

    Model: GT-7264


    Standard conformance: GB/T 11881-2006 6.3 (or specify).

    The GT-7264 is specifically designed to measure the height of shuttlecock ball head.

    Features:
    High-precision height measuring gauge.

/

    Racket Flexibility and Shaft Elasticity Tester

    Model: GT-7630-ACUB


    Standard conformance: GB/T 32608-2016 6.12 and 6.14, GB/T 32609-2016 5.7, QB/T2770-2006 6.8 and 6.12, and QB/T2769-2006 6.7.

    The GT-7630-ACUB is specifically designed to determine the flexibility of badminton and tennis rackets, as well as the elasticity of shafts. 

    Features:
    1. Left bending supports: Utilizes fixed-distance supports to meet the required distance between the specified fulcrums for racket flexibility tests. 
    2. Right bending supports: Utilizes height-adjustable supports to accommodate shafts of different sizes.

/

    Cold Flexing Fixture

    Model: GT-7041-B


    Standard conformance: SAEJ 323 and ASTM D380.

    The GT-7041-B is specifically designed for flexing specimens under cold environments to evaluate their cold cracking characteristics.

/

    Drop Impact Apparatus

    Model: GT-7041-D


    Standard conformance: SAE J323-04 method B.

    The GT-7041-D is specialized to determine the brittleness characteristics of flexible plastic materials.

/

    Terminal Pull-Off Test Grips

    Model: EA-5A

     

    The EA-5A grips are suitable for pull-off tests on single-ended crimped wire terminals.

/

    Aglet Pull-Out Fixture

    Model: FB-2-AT

     

    The FB-2AT is specifically designed to assess the bonding strength of various aglets in aglet pull-out strength testing.

/

    Pliers Grips

    Model: FA-C

     

    The FA-C pliers grips are specifically designed to conduct tensile testing on a variety of materials such as rubber, plastics, metal, and leather.

    Features:
    With increased size and thick adjusting screws, the new pliers grips provide a significant improvement in durability and strength and are capable of withstanding test capacities up to 400kg.

/

    Floor Coatings Bonding Strength Fixture

    Model: FCA-1

     

    Standard conformance: GB/T 22374-2018 6.3.9.

    The FCA-1 fixture is specifically designed for conducting tensile bonding strength tests on floor coatings.

/

    Rigid Substrates Pull-Off Test Grips

    Model: FCA-2

     

    Standard conformance: GB/T 5210 9.4.2.

    The FCA-2 grips are specifically designed for conducting adhesion pull-off tests on rigid substrates.

/

    Multi-Purpose Substrates Pull-Off Test Grips

    Model: FCA-3

      

    Standard conformance: GB/T 5210 9.4.1 and GB/T 5210 9.4.3.

    The FCA-3 grips are specifically designed for conducting adhesion pull-off tests on both rigid and deformable substrates.

    Features:
    The FCA-3 grips are versatile and capable of conducting pull-off tests on both rigid and deformable substrates. For testing on deformable substrates with poor adhesion, coating application on both sides of the substrate is permitted.

/

    Edge Crush Test Guide Blocks

    Model: GT-6011-2-3A

     

    Standard conformance: ISO 3037.

    The edge crush test guide blocks are specifically designed to support corrugated fiberboard sample and keep it perpendicular to the compression platen surfaces during the edge crush test.

/

    Pneumatic Sample Forming Machine

    Model: GT-7016-FM 

     

    The GT-7016-FM is designed to condition and tamp rubber specimens for rubber resilience testing.
     

Back to the top